colorlight i9 plus Receiving Card

Colorlight i9 plus Receiving Card is part of LED Display Control System. Colorlight i9 Receiving Card is a universal receiver card.

Description

colorlight logo

Colorlight i9 plus Receiving Card

Colorlight i9 plus Receiving Card

i9 plus Receiving Card

Colorlight i9 plus Receiving Card is  part of  LED Display Control System. Colorlight i9 plus Receiving Card is a high-end and universal receiver card specially introduced in color flash, with a small size, with 63 * 33mm; it uses DDR2 SODIMM interface to easily integrate into the line board or unit panel of the LED display, implement the LED display module High integration, which greatly promotes the design of the LED display unit and the structure.

Features

  • Supports 32 sets of RGB signal parallel output
  • Loading capacity: 512×384 pixels
  • Supports HDR
  • Low latency
  • Supports brightness and chromaticity point-by-point calibration
  • Supports better gray at low brightness
  • Supports color temperature adjustment
  • Supports color gamut adjustment
  • Seam compensation
  • Support any pumping row, pumping column and pumping point
  • Supports smart module to save calibration coefficients and other information on module
  • Temperature, humidity, power supply control voltage monitoring on cabinet and fan control
  • Supports network cable status monitoring
  • Supports any scan type from static to 64 scan
  • Wide working voltage range with DC 3.3~6V.
  • Compatible with all series of Colorlight sending devices

Specification

Control System Parameters
Sending Device All series of Colorlight sending devices
Control Area of Every Card Full-color: 512×384 pixels
Network Port Exchange Supported, arbitrary use
Gray Level Maximum 65536 levels
Display Module Compatibility
Chip Supports PWM chips
Scan Type Supports any scan type from static to 64 scan
Module Specifications Support Supports16384 pixels within any row, any column
Cable Direction Supports route from left to right, from right to left, from top to bottom, from bottom to top
Data Sets 32 sets of parallel RGB full color data, 64 sets of serial RGB data
Data Folded Supports 2~8 any discount to improve refresh rate
Data Exchange 32 sets of data any exchange
Module Snapshot Supports any pumping point
Compatible Device and Interface Type
Communication Distance UTP cable≤140M;CAT6 cable≤170M;Optic fiber transmission distance unrestricted
Compatible with Transmission Equipment Gigabit switch, fiber transceiver, optical switches
Size 67.6×35.5mm
Input Voltage DC 3.3V~6V
Rated Current 0.5A
Rated Power 2.5W
Storage and Transport Temperature -50℃~125℃
Operating Temperature -25℃~75℃
Body Static Resistance 2KV
Weight 9.5g
Monitoring Function
Temperature Monitoring Cabinet temperature monitoring between -25℃~75℃

1 port for each card

Humidity Monitoring Receiver card humidity monitoring between 20%~95% RH

1 port for each card

Bit Error Monitoring Monitor the total number of data packets and error packets to check network quality
Supply Voltage Monitoring 4 ports for supply voltage monitoring
Full Color LCD Display Panel Supported
Multi-function card Monitoring cabinet door, fan and smoke when in conjunction with M3
Pixel Level Calibration
Brightness Calibration Supported
Chromaticity Calibration Supported
Other Features
Hot Backup Supports loop backup, dual receiver card backup and dual power supply backup
Shaped Screen Supports various freeform display, spherical display, creative display, etc. through the data arbitrary offset

 

Interface

S/N Name Function Remarks
1 Signal indicator light Flashes once per second Receiving card: normal working,

Network cable connection: normal

Flashes 10 times per second Receiving card: normal working, Cabinet: Sorting & Highlight
Flashes 4 times per second Receiving card: Backing up network port (Loop backup status)
2 Power indicator light The red indicator light shows that the power supply is normal
3 Fixed hole Used to reinforce the receiving card to improve vibration resistance
4 DDR interface Connects with display’s HUB board or unit plate From the diagram above, the left side of the guide plate is first pin (Viewing from the front of card)

 

Instructions Definition Pin No. Definition Instructions
Ground connection GND 1 2 D5V Power supply
GND 3 4 D5V
GND 5 6 D5V
GND 7 8 D5V
GND 9 10 D5V
GND 11 12 D5V
Do not connect NC 13 14 NC Do not connect
Network port 1 signal pin

Recommended use isolation transformer

eth1_p1 15 16 eth2_p1 Network port 2 signal pin

Recommended use isolation transformer

eth1_n1 17 18 eth2_n1
NC 19 20 NC
eth1_n2 21 22 eth2_n2
eth1_p2 23 24 eth2_p2
NC 25 26 NC
eth1_p3 27 28 eth2_p3
eth1_n3 29 30 eth2_n3
NC 31 32 NC
eth1_n4 33 34 eth2_n4
eth1_p4 35 36 eth2_p4
Do not connect NC 37 38 NC Do not connect
Ground connection GND 39 40 GND Ground connection
Indicator light LED_BTN_LED 41 42 A Display control:
1. ABCDE for row decoding signal;
2. LED_LAT for signal lock;3. LED_OE control LED display enable, like a switch, it is GCLK when the led display use PWM chip
Temperature monitoring LED_TEMP 43 44 B
Humidity monitoring LED_HUM 45 46 C
Fan control LED_FAN 47 48 D
Blanking LED_CTRL 49 50 E
Serial clock LED_SCLK 51 52 LED_LAT
LED_SCLK_S 53 54 LED_OE
GND 55 56 GND
RGB output LED_R1 57 58 LED_R2 RGB output
LED_G1 59 60 LED_G2
LED_B1 61 62 LED_B2
LED_R3 63 64 LED_R4
LED_G3 65 66 LED_G4
LED_B3 67 68 LED_B4
LED_R5 69 70 LED_R6
LED_G5 71 72 LED_G6
LED_B5 73 74 LED_B6
LED_R7 75 76 LED_R8
LED_G7 77 78 LED_G8
LED_B7 79 80 LED_B8
LED_R9 81 82 LED_R10
LED_G9 83 84 LED_G10
LED_B9 85 86 LED_B10
LED_R11 87 88 LED_R12
LED_G11 89 90 LED_G12
LED_B11 91 92 LED_B12
LED_R13 93 94 LED_R14
LED_G13 95 96 LED_G14
LED_B13 97 98 LED_B14
LED_R15 99 100 LED_R16
LED_G15 101 102 LED_G16
LED_B15 103 104 LED_B16
Ground connection GND 105 106 GND Ground connection
GND 107 108 GND
RGB output LED_R17 109 110 LED_R18 RGB output
LED_G17 111 112 LED_G18
LED_B17 113 114 LED_B18
LED_R19 115 116 LED_R20
LED_G19 117 118 LED_G20
LED_B19 119 120 LED_B20
LED_R21 121 122 LED_R22
LED_G21 123 124 LED_G22
LED_B21 125 126 LED_B22
LED_R23 127 128 LED_R24
LED_G23 129 130 LED_G24
LED_B23 131 132 LED_B24
LED_R25 133 134 LED_R26
LED_G25 135 136 LED_G26
LED_B25 137 138 LED_B26
LED_R27 139 140 LED_R28
LED_G27 141 142 LED_G28
LED_B27 143 144 LED_B28
LED_R29 145 146 LED_R30
LED_G29 147 148 LED_G30
LED_B29 149 150 LED_B30
LED_R31 151 152 LED_R32
LED_G31 153 154 LED_G32
LED_B31 155 156 LED_B32
Ground connection GND 157 158 GND Ground connection
Smart module
(Save calibration coefficients in module)
LED_SPI_SCK 159 160 LED_SPI_SDI Smart module
(Save calibration coefficients in module)
LED_SPI_CS1 161 162 LED_SPI_CS2
LED_SPI_SDO1 163 164 LED_SPI_SDO2
LED_SPI_CS3 165 166 LED_SPI_CS4
LED_SPI_SDO3 167 168 LED_SPI_SDO4
LED_SPI_CS5 169 170 LED_SPI_CS6
LED_SPI_SDO5 171 172 LED_SPI_SDO6
LED_SPI_CS7 173 174 LED_SPI_CS8
LED_SPI_SDO7 175 176 LED_SPI_SDO8
Power supply monitoring LED_M1 177 178 LCD_CTRL5 Reserved
LED_M2 179 180 RS LCD
LED_M3 181 182 SDA
LED_M4 183 184 SCL
LED_M5 185 186 CS
Reserved NC 187 188 RCV_BK1 Dual card backup
NC 189 190 RCV_BK2
LCD GPIO0 191 192 LED_BLUE RGB tricolor indicator
GPIO1 193 194 LED_GREEN
GPIO2 195 196 LED_RED
GPIO3 197 198 RCV_BK6 Reserved
Ground connection GND 199 200 GND Ground connection